n-a
... Vezi mai mult
| Cod produs: | R80524 |
| Producător: | Terra |
- Găsit undeva mai ieftin?Spune-ne
- SEAP? Publicăm imediat!
- Instalator sau revanzător?Cere ofertă
73003 lei
The SRM-524 R80524 multiswitch has been equipped with LNB switch for selecting quatro or wideband LNB
The DC IN connector allows for powering the Terra SRM-524 R80524 multiswitch from the R71468 20 VDC power supply. The DC switches enable using the H/V lines for transmitting the 20 VDC supply voltage.
The programmable SRM-524 R80524 multiswitch has one pair of Legacy /dSCR + DTT outputs. The outputs allow in dSCR mode for independent operation of up to 32 SAT dSCR receivers/STBs, fed in via two coaxial cables (16+16, default configuration) or via one coaxial cable (32 from one output in Unicable II standard, after reprogramming with the PC102W R80561 programmer) and through a distribution network based on typical passive satellite taps and splitters operating in the 5-2400 MHz frequency range. In Legacy mode, each of the outputs can be used as typical SAT output (like in Universal LNBs or standard (legacy) multiswitches) for connecting a legacy SAT TV receiver).
Key features
- Built-in LNB switch for selecting wideband or quatro LNB
- One pair of dSCR/Legacy tap outputs
- DISEqC control connector allowing for connecting PC102W R80561 programmer and simultaneous configuration of all outputs
- Full compatibility with EN50494 standard - Unicable I - 8 UBs (User Bands) from each of the 4 pairs
- Full compatibility with EN50607 - Unicable II - 32 UBs (User Bands) from each of the 3 pairs
- AGC system ensures stable 84 dBμV output level in the SAT path and 82 dBμV level in the terrestrial path
- Possibility of using receivers supporting EN50607 and EN50494 standards in the same subsystem (8 x EN50494 + 24 x EN50607)
- Power supply diagnostics by means of LEDs located on the device housing.
The single-cable cascadable SRM-524 R80524 multiswitch allows for distribution of DVB-S/S2 signals from one satellite (or, using wideband LNBs, from two satellites) and terrestrial signals (DVB-T, DAB/FM radio). The satellite signals can be distributed by means of dSCR technology (digital Satellite Cable Router), requiring only one coaxial line and satellite splitters to provide the signals to compatible SAT receivers, along with terrestrial signals that can be received by standard televisions and radios. The cascadable SRM-524 R80524 multiswitch fully supports receivers operating in two dynamic modes: SCR (Unicable I - 8 User Bans) and dSCR (Unicable II - 32 User Bands).
The SRM-524 multiswitch has 5 inputs (four polarization/band pairs (VL–HL–VH–HH) plus active terrestrial path (DTT)) and two outputs: dSCR (each allowing for independent operation of up to 16 SAT dSCR receivers/STBs fed via one coaxial cable - EN50607 standard) or operating as Legacy (typical SAT output like in Universal LNBs or standard (legacy) multiswitches for connecting a legacy SAT TV receiver).
The built-in Automatic Gain Control (AGC) appropriately adjusts the multiswitch gain to ensure preset, constant output signal levels.
The SRM-524 multiswitch has 5 inputs (four polarization/band pairs (VL–HL–VH–HH) plus active terrestrial path (DTT)) and two outputs: dSCR (each allowing for independent operation of up to 16 SAT dSCR receivers/STBs fed via one coaxial cable - EN50607 standard) or operating as Legacy (typical SAT output like in Universal LNBs or standard (legacy) multiswitches for connecting a legacy SAT TV receiver).
The built-in Automatic Gain Control (AGC) appropriately adjusts the multiswitch gain to ensure preset, constant output signal levels.
By default, all outputs of the SRM-524 R80524 multiswitch are configured as Legacy (controlled by 14/18 V and 0/22 kHz commands from SAT receivers). Any output switches to Unicable dynamic mode after receiving DiSEqC command compliant with EN50494/EN50607 standard. This means that each individual output can feed via a single coaxial cable and 5-2400 MHz satellite splitters up to 16 receivers (EN50607).
The device can operate in two modes;
- DYNAMIC - fixed output frequencies (User Bands) allocated for individual dSCR/Unicable receivers (distribution via single coaxial cable to up to 8 (EN50494 - UNICABLE I) or 32 (EN50607 - UNICABLE II) receivers);
- STATIC - fixed input and output frequencies, IF/IF conversion allowing for distribution of signals from 32 satellite transponders to an unlimited number of receivers (the practical limit results only from the attenuation of the passive distribution network).
The programming of dSCR multiswitches is performed by the dedicated PC102W R80561 programmer.
The die-cast housing provides high screening efficiency by preventing the penetration of interfering signals to the unit.
The multiswitch should be powered from an external power supply, e.g. PS202F R71468 (20 VDC, 2 A).
The table shows the default settings of the SRM-524 R80524 multiswitch (operation mode - DYNAMIC, 16+16 User Bands, Bandwidth, Level), which can be modified by the dedicated PC102W R80561 programmer.
There are many models of satellite receivers available on the market today. Not all of them support SCR/UNICABLE system compliant with EN50494 and/or EN50607 standard. In the case of implementing solutions based on the standards, all receivers that will be used by subscribers must support SCR/UNICABLE technology. As an example, a list of popular satellite receivers available in the Polish market and supporting single-cable multiswitches is provided below:
Ferguson:
- Ferguson Ariva 154 Combo
- Ferguson Ariva 253 Combo
- Ferguson Ariva 4K Black
- Ferguson Ariva 4K Combo Black
- Decoder HD 5000
- Decoder HD 5500s
- EVOBOX PVR
- BOX+
- mediaBOX+
- turboBOX+
- wifi Premiumbox+
- UltraBox NC+
Recommended library article:
Single-cable multiswitches -TERRA dSCR (Unicable system)
Single-cable multiswitches -TERRA dSCR (Unicable system)
4F">
The diagram above shows an example installation based on the cascadable single cable dSCR multiswitch with active terrestrial path and AGC function
Specifications
| Name | SRM-524 | ||
| Code | R80524 | ||
| SAT IF band (LNB wideband - LO = 10410 MHz) | 290-2340 MHz | ||
| SAT IF band (LNB wideband - LO = 10400 MHz) | 300-2350 MHz * | ||
| SAT IF band (LNB quatro - LO = 9750 MHz / LO = 10600 MHz) | 950-2150 MHz | ||
| SAT IF - output | 950-2150 MHz | ||
| Terrestrial path band | 47-862 MHz | ||
| SAT IF in/out trunk lines | 4 | ||
| Terrestrial path in/out line | 1 | ||
| dSCR/Legacy tap outputs | 2 (1 pair) | ||
| SAT IF trunk line attenuation | < 4 dB | ||
| Terrestrial trunk attenuation | < 4 dB | ||
| Return loss / impedance | > 10 dB / 75 Ω | ||
| SAT IF input level (one channel) | 65-105 dBµV | ||
| Terrestrial input level (eight channels) | 55-85 dBµV | ||
| Terrestrial path noise figure | <8 dB | ||
| dSCR+DTT user bands (dSCR mode) | max 32 (configurable) | ||
| dSCR+DTT user band width (dSCR mode) | 20...60 MHz (configurable) | ||
| dSCR+DTT user bands (dSCR mode) output level with AGC | 84 dBµV (configurable) | ||
| dSCR+DTT user bands (Legacy mode) output level with AGC (SAT) | 78 dBµV (typical) | ||
| dSCR+DTT user bands (Legacy mode) output level with AGC (DTT) | max. 82 dBµV (for 8 channels, configurable) | ||
| Isolation between SAT IF inputs | > 30 dB | ||
| Isolation between SAT IF input and dSCR output | > 30 dB | ||
| Isolation between SAT IF and DTT input | > 25 dB | ||
| SAT IF trunk DC pass-through current capacity | max. 3.2 A 1.6 A for one line | ||
| DTT line DC pass-through current capacity | max. 200 mA | ||
| Current consumption by H lines | max. 290 mA | ||
| Current consumption by V lines | max. 280 mA | ||
| Current consumption from H/V lines (DC IN 20 VDC) | 270 mA | ||
| Current consumption from H/V lines (DC IN 18 VDC) | 310 mA | ||
| Current consumption from H/V lines (DC IN 15 VDC) | 390 mA | ||
| Current consumption from a SAT receiver (18 VDC) | max. 20 mA | ||
| Current pass from DC IN(H) to H trunk line (switch) | max. 1.6 A | ||
| Current pass from DC IN(V) to V trunk line (switch) | max.1.6 A | ||
| Operating temperature range | -20ºC... +50ºC | ||
| Dimensions/weight | 227x134x30 mm/0.80 kg | ||
* By default, the multiswitch in wideband mode operates in the 290 MHz...2340 MHz band, which can be changed with the PC102W programmer.
R80524
V-ar putea plăcea și
produse în această categorie
1.017,46 lei
1.017,46 lei
1.017,46 lei
... Vezi mai mult